







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Windows & Doors: The Summerlin Owner’s Guide
We install and service Therma-Tru windows and doors for Summerlin homeowners, and the most common part calls we get land in a clear range: $450 to $1,800 for a single failed component like a multi-point lock, hinge set, or sill repair, and $4,500 to $15,000 when the whole door or window unit has reached the end of its line. Failures usually announce themselves the same way. A Therma-Tru Smooth-Star or Fiber-Classic entry door stops latching cleanly in July. The deadbolt turns but won’t seat. Hinges on a patio door start sagging after another dry summer.

Summerlin sits at roughly 3,000 feet in the Mojave, and the swing from a 105°F July afternoon to a 35°F January night is the single biggest stressor on these components. We’ll get to part matching, real prices, and the honest DIY line below.
Key Takeaways
- Therma-Tru part numbers are stamped on the door edge label and inside the hinge jamb; that label is what makes an exact match possible.
- Component repairs in Summerlin run $450 – $1,800 installed; full unit replacement runs $4,500 – $15,000.
- Most “the door is broken” calls turn out to be a $200 lock, hinge, or sill part, not a door.
- We’re an independent service provider. We’re not affiliated with Therma-Tru.
Which Therma-Tru Models This Applies To

Therma-Tru builds to a handful of product families, and the part you need depends on which one is on your house. The entry door lines you’ll most often see in Summerlin are Fiber-Classic (a smooth, woodgrain-textured fiberglass skin), Smooth-Star (a flat, paintable fiberglass door), and Classic-Craft (the heavier, premium fiberglass series). Patio and glazed units typically come from the Fiber-Classic or Smooth-Star families as well, while the windows side is usually handled by Therma-Tru’s sister lines under the same ownership group.
Here’s how to identify what you have before you call anyone:
- Look at the door edge label. Therma-Tru stamps a sticker on the hinge-side edge, and it carries the model line and often the part family for the slab.
- Open the door and check the hinge jamb. The hinge brand and screw pattern tell us exactly which replacement hinge set seats without new pilot holes.
- Photograph the sill and threshold. Adjustable sill systems changed design across production runs, and a two-photo comparison is often enough to pin down the year family.
- Measure the slab. Standard entry slabs are 36 by 80 inches; confirm rather than assume, because a 32-inch unit takes a different lock bore.
On the OEM-vs-aftermarket question for Therma-Tru specifically: for locks, hinges, and sill components we lean OEM when the part is available, because Therma-Tru’s multi-point hardware is machined to its own prep pattern and an off-brand lock often needs new boring. For weatherstrip, sweeps, and seals, a quality aftermarket equivalent is functionally identical and a fair place to save. We’ll tell you which side of that line your part sits on before we order anything.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Windows & Doors Is Failing
A failing component rarely announces itself with a bang. These are the five symptoms we hear about most in Summerlin, with what’s actually behind each one.
- The deadbolt turns but won’t fully seat. Usually a strike plate that has shifted as the frame settles, or a multi-point lock that’s lost its alignment. Left alone, a partially seated bolt means the door isn’t actually secured.
- Hinges sag and the door drags on the sill. The hinge leaves have loosened or the screws have stripped their pilot holes. Common after a long dry season pulls moisture out of the jamb framing.
- Daylight shows around the door or window edge. Seals and weatherstrip have compressed or dried out. In Summerlin’s low-humidity summers, rubber seals stiffen and lose their memory faster than in wetter climates.
- The door is hard to latch in hot weather, easy in cool weather. Thermal expansion in a fiberglass slab is normal, but a swing that changes with temperature points to a hinge or strike-plate issue that needs correcting, not a door that needs replacing.
- Water stains or a soft spot at the sill. A failing sill or threshold seal is letting water in. This one is worth attention early, because a wet sill can rot the rough opening framing behind the trim.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Summerlin, a single failed component repaired or replaced in place runs $450 to $1,800 installed. Whole-unit window replacement runs $4,500 to $15,000, and impact-rated window installation runs $8,000 to $25,000. A full entry door replacement typically falls inside that same window-replacement band, with the premium end driven by the door series and any glazed or sidelight configuration.
What drives the range on any given job:
- Part availability. An OEM hinge set or multi-point lock in stock ships in days; a discontinued series part may need a machined equivalent.
- Scope. Replacing the part versus correcting the framing behind it. A soft sill means rough-opening repair, and that adds labor.
- Door configuration. A single 36-inch slab and a double patio door with a multi-point lock are different jobs, even for the same symptom.
Every job comes with a written price before any work starts, no numbers that move at the door. Completed work is covered by the 365-Day Done Right Promise: if the repair or install doesn’t hold within a full year, we come back and correct it at no charge. We’re part of the Garrison Partners family and held to The Garrison Standard, which means the price and the guarantee are both in your hand before a tool comes out.
DIY or Call Us?
Here’s the honest split. An owner can safely check and sometimes correct a few things: tighten loose hinge screws with a proper pilot hole, replace weatherstrip and door sweeps, clean and lubricate a lock cylinder, and confirm the model label. Those are low-risk and we’re glad to walk you through them.
Where DIY goes wrong on Therma-Tru hardware is the multi-point lock and the door slab fit. A misaligned multi-point system requires an adjustment sequence that, done wrong, strips the mechanism and leaves the door unsecured. Replacing a lock or hinge set on a heavy fiberglass slab means holding the door in place while you work the hardware, and a dropped slab is a much bigger repair than the lock. And if the sill is soft, the real fix is behind the trim, where a homeowner shouldn’t be pulling framing apart on a guess.
None of this is a spring or a live panel, so it isn’t a stop-everything safety call. But the failure cost of getting the lock adjustment wrong is a door that won’t secure. Call (844) 588-0072 and we’ll tell you straight whether the part is worth doing yourself or worth us handling.
FAQs

Fifteen to 25 years for the door slab, but the hardware, seals, and sill are wear items that typically need attention every 8 to 12 years in Summerlin’s climate. The daily temperature swing dries out weatherstrip and loosens hinge screws faster here than in milder markets. When a part goes, replace the part, not the door. Call (844) 588-0072 for a free estimate on the actual scope.
Often, yes. A multi-point lock that’s out of alignment can usually be adjusted rather than replaced, and stripped hinge screw holes can be refilled and re-driven. Seals and sill components are cheaper to replace than to repair. We’ll tell you which is the honest answer before we quote. Call (844) 588-0072 for a free estimate.
A single hinge set, lock, or threshold swap runs one to three hours on site. A sill repair with framing correction can run most of a day. We give you the time window in writing with the price, not after we arrive. Call (844) 588-0072 to schedule your free estimate.
We start with the door-edge label and hinge-jamb markings, cross-reference the model family, and confirm the prep pattern before ordering. For discontinued parts we source a machined equivalent that matches the original prep, and we tell you when we’re using aftermarket instead of OEM. Parts are ordered to the job, matched to your door, and installed. Call (844) 588-0072 for a free estimate.
If a Therma-Tru door or window in your Summerlin home is failing, the fastest path to a straight answer and a written price is a call. Bradford Remodeling Co Summerlin installs and services Therma-Tru doors and windows, backed by a written price before work starts and the 365-Day Done Right Promise covering every completed project. We also work with KraftMaid, Cambria, and Silestone on the projects that touch them. Call (844) 588-0072 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












