







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Kitchen Remodeling: The Summerlin Owner’s Guide
A failed Mr-Glass component in a Summerlin kitchen usually shows itself before it fully breaks: a drawer that no longer lines up, a hinge that lets the door sag, a soft-close mechanism that quit closing softly. We install and replace Mr-Glass-compatible kitchen parts and full kitchens across Summerlin, with typical installed kitchen remodeling running $14,000 – $45,000 depending on scope. Smaller part-level repairs sit well below that. Bradford Remodeling Co Summerlin is an independent service provider – we’re not affiliated with Mr-Glass, we’re the crew that matches the right part to your model and installs it to spec. Most owners catch the problem when a door stops sitting flush or the soft-close feature gives out on a heavily used cabinet.

Key Takeaways
- Mr-Glass kitchen parts are model-specific. The model number matters more than the part name.
- Installed kitchen remodeling in Summerlin runs $14,000 – $45,000; cabinet-only work runs $4,000 – $13,000.
- Soft-close hinges and drawer glides are the first parts to fail in Summerlin’s dry indoor air.
- Every project gets a written price before tools come out, plus the 365-Day Done Right Promise.
Which Mr-Glass Models This Applies To

Mr-Glass has built kitchen cabinetry and component systems across several product lines, and the parts don’t swap cleanly between them. A soft-close hinge from one series will bolt onto a cabinet from another series and look correct – until the door swings 3 millimeters out of alignment because the hinge cup depth and overlay differ. That’s the compatibility gotcha most homeowners hit: the hinge fits, the door doesn’t sit right, and the next six months are spent tightening screws that keep backing out.
To identify the right part, start with the label. Mr-Glass puts a model and series sticker inside the cabinet door or on the back panel of a drawer box – pull the door open and look at the upper inside edge. If the label is gone, measure the hinge cup bore (the round hole the hinge drops into), the door overlay, and the drawer glide length. Those three numbers narrow the correct replacement quickly. Standard cup bores run 35mm, but Mr-Glass has used other sizes on some lines, so measure rather than assume.
On the OEM-versus-aftermarket question: for structural parts like drawer glides and hinges, a matched OEM-equivalent from a documented brand is the safer call because the spec is traceable. For cosmetic parts like shelf pins or cover caps, a quality aftermarket match works fine. We work from a documented roster of name-brand materials – KraftMaid, Cambria, and Silestone among them – so when we source a compatible part, the specification is written down, not guessed. If your kitchen also carries KraftMaid, Cambria, or Silestone elements alongside the Mr-Glass components, we handle those in the same scope.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mr-Glass Kitchen Remodeling Is Failing
These are the symptoms Summerlin homeowners describe when they call us about a Mr-Glass kitchen issue. Each points to a different underlying cause.
- Doors that hang unevenly or rub the frame. A worn hinge or a hinge whose screws have pulled from the cabinet material lets the door drop. Left alone, the rubbing wears the finish off the door edge.
- Drawers that stick, wobble, or fall off their track. The drawer glide has worn or the mounting screws have loosened from repeated load. A glide that’s lost its roller tension will keep jamming no matter how many times you re-seat it.
- Soft-close that slams instead of easing shut. The damping mechanism inside the hinge or glide has failed. This is the most common Mr-Glass component failure we see, and it’s usually the first sign the part is past its service life.
- Cabinet boxes that have separated at the joints. In Summerlin’s low indoor humidity, wood and composite cabinet materials shrink slightly over the seasons, and glue joints can open. A joint that’s pulling apart needs the box re-squared, not just re-glued.
- A smell or soft spot near the sink base or dishwasher. Water from a slow leak has reached the cabinet substrate – the structural board under the finish. By the time you smell it, the substrate is often compromised and needs replacement, not repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed kitchen remodeling in Summerlin runs $14,000 – $45,000. That span covers everything from a focused cabinet and countertop refresh to a full layout change with new cabinetry, surfaces, and fixtures. The number that applies to you depends on scope, not on how the job is marketed.
| Scope | Installed price range (Summerlin) |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: cabinet count and door style, whether the layout moves (which means plumbing and electrical rough-in), countertop material, and whether the cabinet boxes themselves are sound. If only the hinge or glide failed and the boxes are solid, you’re looking at part-level work far below the table above – we price it that way and tell you plainly when a repair beats a replacement.
Parts and labor are itemized in the written price you get before any work starts. No numbers move at the door. Every completed project carries the 365-Day Done Right Promise – a full-year written guarantee. If the work fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
There’s a safe split here. You can check the model label, measure the hinge cup and overlay, tighten visible screws, and confirm whether a glide is seated correctly. Those are inspection steps, and they help us quote the right part when you call.
Where DIY goes wrong: cabinet boxes are heavy, wall-mounted uppers are heavier, and a cabinet that comes off its mounting is a serious injury risk. Replacing a failed hinge or glide inside a cabinet that’s already installed is tight work that most homeowners can’t do cleanly without damaging the door face or stripping the screw holes further. And if a water leak has reached the substrate, a surface patch hides the problem while the rot spreads – which turns a small repair into a cabinet replacement. If you smell moisture or see a soft spot, stop and have it looked at. Call (844) 588-0072 and we’ll tell you over the phone whether it’s a part swap or something bigger. Estimates are free.
FAQs

How long do Mr-Glass kitchen hinges and glides last? Most soft-close hinges and drawer glides last 8 to 12 years under normal use, and heavily used doors – the ones you open a dozen times a day – often fail sooner. In Summerlin’s dry indoor air, the plastic damping components can dry out and lose tension before the metal parts wear. Call (844) 588-0072 and we’ll assess yours and tell you honestly whether it’s time to replace.
Can a failed Mr-Glass kitchen part be repaired instead of replaced? Often yes. A loose hinge can sometimes be re-seated with a proper fix, and a drawer glide can occasionally be re-tensioned. But a hinge whose damping mechanism has failed internally, or a glide that’s cracked, can’t be repaired – it has to be replaced. We check first and tell you which one it is before quoting. Call (844) 588-0072 for a free estimate.
How long does a Mr-Glass kitchen part swap take? A single hinge or glide replacement is usually under an hour per unit. A full set of soft-close hinges across a standard kitchen runs about half a day. Cabinetry or countertop work runs longer, and we write the timeline into your estimate so you know what to expect. Call (844) 588-0072 to schedule.
How do you source the right Mr-Glass part for my model? We match by model number and series, confirmed against your cabinet’s label or by measurement when the label is missing. We source from documented, name-brand materials with traceable specifications, so the part you get is the part that was quoted. If a compatible OEM-equivalent isn’t available, we tell you what the alternative is and why. Call (844) 588-0072 for a free estimate.
Bradford Remodeling Co Summerlin gives you the written price before any work starts, background-checked and uniformed technicians on every job, and a live person on the phone 24/7 – no voicemail, no callback queue. When we close a job, you get a clean site, a documented scope, and your signed written guarantee in hand. Call (844) 588-0072 to schedule your free estimate and find out exactly what your Mr-Glass kitchen needs.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












