







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Fence Installation: The Summerlin Owner’s Guide
Replacing a Moen fence installation component in Summerlin runs $3,500 to $9,000 installed, and the job is scheduled, not emergency work – we book it into the calendar with a written price before the crew touches the gate. Owners usually find the problem the same way: a gate that drags on the pavers after a summer of 110°F swings, a post base that’s tilted a quarter inch past plum, or a latch set from a Moen-series accessory line that stopped catching somewhere between the pool deck and the side yard. You notice it on the walk out to the mailbox, not from a manual.

We’re Bradford Remodeling Co Summerlin, and we’re an independent contractor – not affiliated with Moen. We install, repair, and replace fence and gate components from documented manufacturers, and we do it under a written price and the 365-Day Done Right Promise. The page below is for the Summerlin owner who already knows which part failed and wants the real number.
Which Moen Models This Applies To

Moen’s residential fence-adjacent hardware lines (gate hardware, decorative post caps, latch and hinge kits sold alongside fence systems) are not the same catalog as their plumbing trim, and that distinction trips people up at the counter. The part number on your box is the only reliable cross-reference. Look for a label on the gate hardware housing, inside the latch cover, or on the installer’s paperwork; if the label is worn, measure the setback (the gap from the post face to the hinge plate) and the post cap diameter in inches and match those to the spec sheet, not the model name.
OEM versus aftermarket: for Moen-specific gate hardware, OEM parts fit without shimming and hold the manufacturer’s material spec – which matters in Summerlin, where UV exposure strips cheap powder coating in about two summers. Aftermarket equivalents that meet the same mechanical spec can save money on a latch or cap, but for hinges and post-base plates, the tolerances are tight enough that a spec-matched aftermarket part is a gamble we don’t recommend. If you’re also updating surfaces nearby in the same project window, we work with Cambria, Silestone, and KraftMaid on the interior side, and the same documented-brand discipline applies outdoors.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Fence Installation Is Failing
Five symptoms we see repeatedly on Summerlin fence lines, and what’s actually causing each:
- Gate sag or drag on the pavers. The hinge plate has fatigued or the post base has settled; the gate isn’t the culprit, the anchor is. Left alone, the plate cracks at the screw line.
- Latch won’t catch or pops open with a nudge. The strike plate has shifted from the seasonal ground movement Summerlin sees in clay-heavy beds near the washes. A latch that doesn’t catch is a safety problem, not a nuisance.
- Rust bloom at the screw heads or hinge barrels. Moisture intrusion from irrigation overspray or monsoon rain cycling into a part whose finish has broken down. Cosmetic at first, structural once the threads start to fail.
- Post cap wobble or loss after high wind. The cap adhesive or friction fit has failed; caps are the first component to go in a Summerlin wind event. A missing cap lets water into the post top.
- Visible gap or lean at the post base. The concrete footing has shifted or the base plate hardware has backed out. This is the one to take seriously – a leaning post is a gate-injury risk if it gives.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed fence components in Summerlin run $3,500 to $9,000. Here’s what drives the number:
| Scope | Installed $ Range |
|---|---|
| Vinyl fence installation | $3,500 – $9,000 |
| Aluminum fence installation | $4,000 – $10,000 |
Linear footage, gate count, post-base condition (a failed footing with concrete work vs. a straight hardware swap), and material selection move the range. Every quote is a written line-item – parts and labor separated – and the price doesn’t move at the door. All completed work is covered by the 365-Day Done Right Promise: if the installation fails within a year, we come back and correct it at no charge. Free estimate, no pressure.
DIY or Call Us?
What you can safely do yourself: read the label, measure the setback and post diameter, photograph the hardware, and confirm the part number. What you shouldn’t do yourself: unbolt and reset a loaded gate or re-anchor a post base on a footing you haven’t assessed. A gate is heavy and under load the moment the hinge comes off, and a post that’s been leaning can let go while you’re underneath it. We don’t hand out step-by-step install instructions for loaded gate hardware – a trained technician sets the anchor, checks the swing, and calls it plumb before the gate goes back on. Our technicians have up to 22 years of experience. Background-checked, uniformed technicians on every job, a live person answering the phone 24/7, and a written price before any work starts.
FAQs

How long does a Moen fence installation last in Summerlin? Expect 10 to 15 years for a quality vinyl or aluminum system with UV-stable coating, provided the post bases were set correctly and the hardware finish holds. Summerlin’s combination of intense sun and monsoon-season moisture is the real test – hardware is the first failure point, usually within 5 to 7 years. Call (844) 588-0072 for a free estimate on a full replacement.
Can it be repaired instead of replaced? Often, yes – a single failed latch, hinge set, or post cap can be swapped without replacing the whole fence line. A failed footing or multiple sagging hinges usually means replacement. We’ll tell you which you’re looking at in the written estimate, with the line items priced separately.
How long does the swap take? A hardware-only replacement is typically a single-day job. A full fence installation in Summerlin runs two to four days depending on linear footage and gate count. The schedule is documented before we start, and the site is cleaned and the written guarantee is in your hand at close.
How do you source the Moen part? We match your part number or measured spec against the manufacturer’s current catalog and order from a documented supplier. We don’t carry parts on a truck – the spec comes first, then the order. If the exact part is discontinued, we’ll tell you and quote the spec-matched equivalent in writing.
Related work we handle in Summerlin: kitchen and bathroom remodels, cabinet and countertop installation (KraftMaid, Cambria, Silestone, and more), roof replacement and repair, window replacement, driveway and paver work, and home additions – all under the same written-price, 365-Day Done Right Promise discipline. As a member of the Garrison Partners family, every Bradford location is independently owned and operated and held to The Garrison Standard.
Call (844) 588-0072 to schedule your free estimate. A live person answers, every time. We’ll measure the failed component, put the number in writing, and square the job away.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












