







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
James Hardie Driveway & Pavers: The Summerlin Owner’s Guide
James Hardie doesn’t manufacture pavers or driveway surfacing – it makes fiber cement siding, trim, panels and HardieBacker board. So when a Summerlin homeowner calls us about “James Hardie driveway and pavers,” it almost always means one of two things: Hardy Board panels or trim that were used as a driveway border, planter divider or paver-joint detail, or the fiber cement edge-fascia and trim details that frame a paver driveway where it meets the house. If that’s your situation, a paver driveway install runs $7,000 – $18,000 in Summerlin, and concrete replacements run $4,500 – $12,000. We’re an independent contractor – not affiliated with James Hardie – and we install the trim, fascia and paver system as one finished job.

The symptom tends to show up small. A homeowner notices a trim board at the driveway edge going chalky or a paver joint pulling away from the fiber cement detail and assumes a simple board swap. By the time it’s obvious, water has been tracking under the driveway edge for a season or two of Summerlin monsoon runoff.
Key Takeaways
- James Hardie is a fiber cement manufacturer, not a paver brand – the term refers to trim, fascia or board detail at the driveway and paver line
- Failed trim at a paver boundary is usually a drainage problem first, a material problem second
- We pull the price in writing before any tool comes out, per The Garrison Standard
- Every completed job carries the 365-Day Done Right Promise
Which James Hardie Models This Applies To

The driveways and paver details we see in Summerlin wrap around a handful of James Hardie product lines. The important thing is identifying what you actually have before anyone quotes a replacement.
Most common on exterior trim and driveway-adjacent fascia in Summerlin: HardieTrim boards (often the 5/4-in. or 4/4-in. thickness in the Smooth or Cedarmill finish), HardiePlank lap siding used at garage elevations, HardiePanel vertical panels, and HardieBacker board where a paver patio meets a planter wall. Johnson Hardie fiber cement was rebranded to James Hardie decades ago, so an older home may have trim stamped with either name – it’s the same material family.
Read the back-stamp or edge stamp on any trim board. You’ll see a product name and often a thickness. Thickness matters at a paver joint: a 5/4-in. trim reveals more face above the driveway line than a 4/4-in. and changes how the paver edge detail is stepped. Measure the exposed face – not the total board width. If you match a 4/4-in. board where a 5/4-in. was originally installed, you’ll have a visible step.
On OEM vs aftermarket: James Hardie’s own trim is the safest match, and where the piece is inside your original manufacturer warranty spec, staying OEM is worth the cost difference. For paver-adjacent trim that’s strictly decorative, a quality fiber cement equivalent with matching thickness and a comparable prime finish is a reasonable aftermarket swap. For pavers themselves, James Hardie has no dog in the fight – that’s a separate material system, and we spec Belgian block or concrete pavers against the trim detail, not in place of it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your James Hardie Driveway & Pavers Is Failing
Five things a Summerlin owner should look for at the driveway and paver boundary. Each one tells you what’s really happening underneath.
- Chalky, white residue on trim at the driveway edge. That’s efflorescence or surface breakdown from fiber cement wicking moisture. A single seasonal bloom is normal; a persistent chalk bloom after two monsoon seasons means water is not escaping the joint.
- Trim pulling away from the paver or garage-mullion line. The fastener sitting proud of the substrate, or the substrate itself moving. In Summerlin’s clay-heavy soils, driveway edge settlement is the usual culprit – the trim didn’t fail, the base did.
- Soft spots or crumbling at the board bottom where it meets pavers. Water has been sitting against an unprimed cut edge. Fiber cement needs a primed field cut, and any field cut made during the original install without primer is the first thing to fail.
- Widening gaps at the paver-trim joint. The paver base has shifted or the trim nailing has backed out. Left alone, that gap funnels runoff behind the trim and into the wall assembly.
- Staining, algae or hard-water crust on both the pavers and the fiber cement face. Summerlin’s hard water and calcium-rich irrigation spray leave that crust, and it’s often mistaken for fiber cement failure. It’s usually surface cleaning plus a drainage correction – not a full tear-out.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a James Hardie trim-and-paver detail at a Summerlin driveway edge, a paver driveway install runs $7,000 – $18,000 installed, and a concrete driveway replacement runs $4,500 – $12,000 if you’re replacing the pavement as well. A trim-only repair to the fiber cement detail typically rides in the $400 – $1,800 range depending on linear feet and how much substrate repair is needed.
What drives the range: linear feet of paver or pavement, base preparation depth (Summerlin’s caliche and clay layers can add prep cost), whether driveway edge fascia behind the trim needs repair, and drainage correction if runoff is the root cause. We don’t do “call for a quote” – a written, line-item price is set before any work starts, per The Garrison Standard. That price doesn’t move at the door.

Every completed job – trim, pavers, drainage – carries the 365-Day Done Right Promise. If the repair or install fails inside the 12-month window, we come back and make it right at no charge. That’s a written guarantee in your hand at job close, alongside the documented scope and a clean site.
DIY or Call Us?
You can safely handle the diagnostic side. Check the back stamp on any trim board, measure the exposed face, take a photo of the gap at the paver joint, and look for a consistent low spot where water pools. Cleaning a chalk bloom or hard-water crust off fiber cement is fair game – a soft brush and a garden hose, no pressure washer above about 1,200 psi (high pressure cuts the fiber cement surface and creates the water intrusion you’re trying to prevent).
Where DIY goes wrong: re-fastening or replacing trim at a paver boundary without fixing the drainage behind it just resets the failure clock. And if the underlying paver base has settled, hand-setting a board over a moving substrate is a short-lived repair. This is a professional materials-and-drainage decision, not a caulk-and-go fix. Call our team at (844) 588-0072 and we’ll tell you straight whether you’re looking at trim, drainage, pavement, or all three.
FAQs

James Hardie fiber cement trim is rated for a long service life when it’s installed with primed field cuts and a maintained paint finish, typically 10 to 15 years before a recoat. In Summerlin’s dry heat and intense UV, exterior trim at a driveway edge gets the harshest exposure in the yard, and skipping the recoat shortens that number every year. Call (844) 588-0072 for a free estimate on inspection or replacement – we’ll tell you honestly whether the product or the drainage behind it is the real problem.
Yes, often it can. If the fiber cement trim itself is intact and the failure is a gap at the paver joint or a settled base, a targeted repair that corrects substrate and drainage is usually the better call and cheaper than replacement. Replacing trim over the same failed substrate is the mistake we see most on driveways in Summerlin. Call (844) 588-0072 for a free written estimate – estimates are free and we’ll tell you whether the part or the drainage is the thing that failed.
A trim-only repair at the paver boundary typically runs one to two days; a full paver driveway install runs several days once base prep and drainage correction are factored in. Concrete driveway replacement runs two to three days depending on cure schedule. The exact duration is set in the written scope before work starts, and the crew doesn’t leave the site until the job scope is squared away. Call (844) 588-0072 to get your scope and price in writing.
We source through James Hardie’s established distribution channels and match the product thickness and finish to your existing board, not a “close enough” substitute. We don’t stock parts on a truck or in a warehouse – each board is ordered to spec for your job, which is why the written scope matters. If an OEM match isn’t available in your thickness, we’ll tell you before the job starts and price the aftermarket equivalent honestly. Call (844) 588-0072 for a free estimate.
Yes – Bradford Remodeling Co Summerlin also installs KraftMaid and Wellborn cabinetry, Cambria and Silestone surfaces, plus Kohler and Moen fixtures, on the same written-price and 365-Day Done Right Promise standard. If you’re redoing a driveway-side entry or garage-to-kitchen transition, we can line up the scope as one job. Call (844) 588-0072 for a free estimate.
When the driveway-and-paver detail at your Summerlin house has gone past a coat of paint – a board pulling away, a joint opening up, water tracking where it shouldn’t – the fix is a written scope and a crew that shows up disciplined. Bradford Remodeling Co Summerlin gives you the price in writing before any tool comes out, background-checked technicians on the property, and the 365-Day Done Right Promise on every completed job. Live person answers the phone – call (844) 588-0072 for a free estimate.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












