







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Kitchen Remodeling: The Summerlin Owner’s Guide
Kitchen remodeling for a Dvele home in Summerlin typically runs $14,000 to $45,000 installed, and it’s scheduled work, not emergency work – we plan it around your calendar and put the full written price in front of you before anyone touches a cabinet. This page is for Summerlin owners whose Dvele kitchen has a part that’s failed or is heading that way: doors that won’t sit flush, drawers that drag, a cabinet run that’s pulling away from the wall, or a countertop section that’s cracked at the sink cutout. Most Dvele owners here don’t find the problem on day one. They find it two or three winters in, when a soft-close hinge stops closing softly or a drawer glides crooked and starts rubbing the frame. We work on Dvele kitchens across Summerlin and we’ll tell you plainly which parts are worth matching to the original spec and which ones we replace with a documented name brand. Bradford Remodeling Co Summerlin is an independent contractor and is not affiliated with Dvele.

Which Dvele Models This Applies To

Dvele builds a modular, panelized home, which means the kitchen cabinetry, appliance spacing, and countertop layout are set by the model’s factory drawings – not by the on-site carpenter’s judgment. The practical effect for a Summerlin owner is that box dimensions, drawer glide lengths, and hinge cup placement follow the build’s spec sheet, and a replacement part has to match those numbers, not just look close.
Start by finding the label. Dvele ships a spec and component sheet with the home, usually in a documentation binder or attached inside a cabinet or the mechanical panel. That sheet is what identifies the cabinet line, the drawer glide series, and the countertop material and thickness. If the binder is gone, we take measurements instead: cabinet box depth and width, drawer glide length, hinge cup bore, and the countertop’s edge profile and overhang. Those three measurements – glide length, hinge bore, and countertop thickness – are where aftermarket parts most often miss.
The OEM-versus-aftermarket call is where we earn our keep. For hardware like glides and hinges, a documented aftermarket part from a name we already install, such as a KraftMaid or Wellborn-compatible glide, is often a better long-term choice than chasing an exact factory replacement, because it’s a part we can source again and warranty. For anything structural – a cabinet run out of plumb, a countertop section – matching the original material matters more than matching the label. Cambria and Silestone are both common in Summerlin Dvele kitchens, and we can confirm which by the slab’s stamp or a sample.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Kitchen Remodeling Is Failing
Here’s what a failing part actually looks like in a Dvele kitchen, and the cause underneath each symptom.
- Soft-close doors that slam shut. The hinge’s damper has worn out, not the door. Dampers are the first thing to go on any soft-close hinge, and replacing the hinge is usually cheaper than living with the slam.
- Drawers that drag or jump the track. The glide’s rollers or the track itself has flattened out of true, usually from a drawer that’s been overloaded – and in a Dvele pull-out, that’s often the heavy cookware drawer. Inspect the glide before you blame the drawer box.
- A cabinet run pulling away from the wall. Anchors or shims have shifted, often from Summerlin’s dry heat cycling the framing. This one isn’t a parts swap – it’s a re-anchor and re-plumb, and it’s a safety call if the run is over a countertop.
- Hairline cracks at a countertop cutout. A sink or cooktop cutout is the weakest point in any countertop. CA heat cycling and a slightly undersized cutout will find it. Cambria and Silestone both hold up well, but a cutout that wasn’t sized right is where the crack starts.
- Water damage at the sink base or a toe-kick. A failed supply line, a loose drain, or a backsplash seal that’s let go. This is the one we’d check first if you see swelling in the cabinet floor, because it gets worse quietly.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Replacement and repair pricing for a Dvele kitchen in Summerlin follows the same written-price rule as any full remodel: you get a real dollar range before we start. A full kitchen remodel, which is what a failed cabinet run or a cracked countertop usually leads to once the scope is measured, runs $14,000 – $45,000 installed. A smaller kitchen remodel lands at $9,000 – $20,000. Cabinet installation alone is $4,000 – $13,000, countertop installation $2,000 – $6,500, a backsplash $800 – $2,500, and a kitchen island $3,000 – $10,000.
What moves the number: whether the box is a straight swap or a re-engineer, countertop material and cutout complexity, and whether the rough-in behind the wall is sound. Parts and labor are broken out separately on the quote so you can see what each line costs. Every completed job carries the written price you signed and the 365-Day Done Right Promise – a full-year written guarantee, and if the work fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
Some of this you can check yourself safely. Tighten a loose hinge screw, measure a glide, look for water staining under the sink, and confirm the countertop material from the slab stamp – all fine. Where DIY goes wrong on a Dvele kitchen is the structural and the wet side: re-anchoring a cabinet run that’s pulled away from the wall, resetting a countertop cutout, or chasing a supply line that’s already weeping. A cabinet run over a countertop can come off the wall if it’s not re-anchored to framing, and that’s a real injury risk, not a scare tactic. If your Dvele kitchen has a cabinet run out of plumb or water at the sink base, get a trained eye on it before you post up a ladder. Call (844) 588-0072 and we’ll talk through what you’re seeing, then give you a written price for the fix.
FAQs

Expect soft-close hinges to go 5 to 8 years and drawer glides 7 to 10 under normal use – in Summerlin’s dry heat, the dampers and the plastic glide components are usually what fail first, not the cabinet box. Countertops from Cambria or Silestone should last decades if the cutout was sized right. Call (844) 588-0072 for an honest read on what’s failed and what’s still got life in it.
Often yes. A soft-close hinge, a drawer glide, or a seal can be repaired far cheaper than a cabinet replacement, and we’ll say so if that’s the case. What can’t be repaired is a cabinet run that’s out of plumb or a countertop crack through a cutout – those need re-anchoring or replacement. Call (844) 588-0072 and we’ll tell you which one you’re looking at before you spend a dollar.
A hardware swap – hinges and glides – is typically done in a few hours, while a cabinet run re-anchor or countertop section is a multi-day job with curing time built in. Because this is scheduled work, you’ll know the timeline before the crew starts. Call (844) 588-0072 to get your project on the calendar with a written estimate.
We source replacement parts through a documented brand roster – KraftMaid and Wellborn cabinetry, Cambria and Silestone surfaces, Kohler and Moen fixtures – so every spec is traceable and backed by the manufacturer. We don’t carry parts on a truck, so the part is ordered to the measurements we take. That traceability is what lets us stand behind the work. Call (844) 588-0072 to start with a measurement visit and a free estimate.
Ready for a straight number? Bradford Remodeling Co Summerlin answers the phone with a live person, 24 hours a day. Call (844) 588-0072 to schedule your free estimate, get a written price before any work starts, and plan your Dvele kitchen the right way for Summerlin.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












