







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Summerlin Owner’s Guide
Most residential wood and composite fence work in Summerlin runs $3,500 to $9,000 installed, and fences with a failed gate section or a rotted lower rail land at the low end of that range. We schedule CGI-compatible fence installation by appointment, and in the case of a gate-only or single-section replacement, we can usually get a crew out within a few business days rather than weeks. Owners around here tend to spot the problem the same way: a gate that drags on the pavers in the evening, pickets that have swollen and popped a nail at the rail, or a lower corner that shifts when you push on it after a windy stretch.

Which CGI Fence Models This Applies To

The CGI name covers a broad set of fence systems, and what matters for matching is not the brand on the sticker but four measurements: overall height, post spacing, rail profile, and picket thickness. CGI has been sold in 4-foot, 5-foot, and 6-foot heights with both nominal 2×3 and 2×4 rails, and a post furring strip that has to align with the rail bracket holes. Pull the sticker from the inside face of the gate post (most CGI labels live there), and measure center-to-center post spacing on at least three bays. If you’re swapping a section, note whether the existing pickets are dog-eared or flat-top, and whether the rails are fastened with ring shanks or two-sided clips.
For CGI specifically, the OEM-vs-aftermarket decision leans toward aftermarket for pickets and rails. CGI-compatible components from a regional mill match dimensional specs and cost less than OEM parts, and the material is the same western red cedar or composite blend. Where it pays to stay OEM is on gate hardware and post caps, because a slightly off bracket hole means redrilling into a post you didn’t want to touch. We source both and quote whichever makes sense for the job. One compatibility gotcha we see often: CGI’s older 5-foot configuration used a 4-inch rail that won’t accept a modern 3.5-inch picket clip cleanly, so a patched-in section from a different batch will wobble against the original. Specify the rail profile before ordering.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
A CGI fence fails in recognizable ways, and each symptom points to a specific cause. Here’s what to look for:
- Lower rails and pickets turning soft at the bottom. Ground-contact moisture in Summerlin’s irrigation zones wicks up the picket while the top stays dry, so rot starts at the base and works upward. By the time you see discoloration, the picket has usually lost more than half its strength.
- Gates sagging or dragging. Wind load on a gate that was hung with only one brace is the culprit. The hinge pulls, the post leans, and the gate starts striking the pavers – a fixable problem, but one that gets worse each season.
- Posts leaning after summer heat and winter wind. Posts set in shrink-swell clay will rotate and lean without a proper concrete collar. A lean of more than an inch is the point where re-setting becomes cheaper than straightening.
- Pickets pulling away from rails. Fastener back-out, especially on nails that hammer movement has worked loose. A picket hanging by one fastener is a stress point that will crack the rail if you leave it.
- Rails splitting around the fastener holes. Cedar dries and shrinks in Summerlin’s dry climate, and a rail that was tight at installation will develop hairline checks that widen into cracks where the fastener sits.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

CGI-compatible fence installation in Summerlin lands in the $3,500 to $9,000 range. A single-section replacement with a fresh picket pair, rail, and fasteners sits at the low end. A full run replacement with new posts, concrete footings, gate, and cleanup runs to the top of the range. Variables that move the number: total linear feet, post count, whether the footings have to be re-poured, gate hardware, and site access. We measure before we quote, and we give a written price before any work starts – the same number you see is the number you pay. That’s The Garrison Standard.
Here’s the line-item breakdown, so you can budget:
- Single section replacement: $350 to $850 per section, depending on height and picket profile
- Gate replacement (freestanding): $600 to $1,400
- Post re-set with new concrete: $300 to $550 each
- Full run replacement (under 100 linear feet): $3,500 to $6,500
- Full run replacement (over 100 linear feet): $6,500 to $9,000
All completed work carries the 365-Day Done Right Promise. If a fastener backs out, a rail cracks, or a post leans inside that window, we return and fix it at no charge.
DIY or Call Us?
Some checks are safe to do yourself: walk the fence line and mark leaning posts, test each gate for drag, and look for pickets that flex more than a quarter-inch when you push on them. Measure your post spacing and pull the CGI label – that information makes the quote more accurate.
Where DIY goes wrong on a CGI fence is at the post and gate. A post re-set means digging out the old concrete collar by hand, and a gate reset means either aligning hinges on an existing post (which has almost no margin) or hanging a new gate – which takes a second set of hands and, on a wide driveway gate, a helper on both sides. Repairs to a fallen or leaning fence, especially the sections over a pool barrier or between properties, belong to a trained installer. A pool-barrier fence that isn’t code-compliant creates a real safety problem, and it’s not worth doing wrong. Call (844) 588-0072 to schedule a free estimate.
FAQs

How long should a CGI fence last in Summerlin? A CGI wood fence in Summerlin typically lasts 12 to 18 years, and composite runs 20 to 30. Our dry climate slows rot but drives shrinkage, so the actual lifespan depends on ground contact at the pickets and whether the posts were set with a proper concrete collar. Call (844) 588-0072 for an exact assessment.
Can you repair a CGI fence instead of replacing it? Often yes. A single failed section, a sagging gate, or a cracked rail can usually be repaired instead of replaced, and repair is the right call when the surrounding pickets are still solid. We tell you honestly which is cheaper on the visit, and we quote repair and full replacement side by side. Call (844) 588-0072 for a free estimate.
How long does a CGI fence section replacement take? Most single-section replacements are done in one day, and a full run under 100 feet runs two to three days depending on footing pours. We schedule by appointment, not by “we’ll be there sometime,” and we give you a written start and finish date before the crew arrives. Call (844) 588-0072 to lock in your date.
How do you source CGI-compatible fence parts? We source from regional mills that publish CGI-compatible specifications for pickets, rails, and post profiles, and we verify dimensions against your existing fence before ordering. We don’t claim to stock parts or carry them on a truck – that’s not how we work. We order to spec, confirm the profile matches, and install. Call (844) 588-0072 to get a written price.
Bradford Remodeling Co Summerlin is an independent service provider. We’re not affiliated with CGI, and we’re not a CGI dealer. We install CGI-compatible fence components and other premium fence materials, and we do the same work with KraftMaid cabinetry, Cambria surfaces, and Silestone as part of our remodeling line.
When a fence section fails, what you want is a crew that shows up on the scheduled day, gives you a written price before anyone touches a post, and stands behind the work for a full year. That’s what the 365-Day Done Right Promise means: if a picket warps or a gate sags inside the guarantee period, we return at no charge and correct it. Every price is in writing before work starts, technicians are background-checked and uniformed, and a live person answers the phone any hour – not a voicemail. Call (844) 588-0072, or our team is standing by around the clock for a free estimate. We’ll measure the fence, walk you through the repair-vs-replace call, and hand you a written price the same visit.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












