







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mighty Buildings Driveway & Pavers: The Summerlin Owner’s Guide
We install and replace Mighty Buildings-compatible driveway and paver systems in Summerlin, and installed pricing typically runs $7,000 – $18,000 for a paver driveway and $3,500 – $11,000 for a paver patio, with concrete driveway work at $4,500 – $12,000 and driveway replacement at $5,000 – $14,000. Every job gets a written price before we start and the 365-Day Done Right Promise on the finished work. Most Summerlin owners don’t notice the failure all at once. It shows up as one paver that rocks underfoot, then a hairline gap in the joint sand along the garage apron, then water pooling where it used to drain. By the time it’s obvious, the base course has usually already moved.

Bradford Remodeling Co Summerlin is an independent service provider. We’re not affiliated with Mighty Buildings, and we don’t claim to be. We work on their assemblies because Summerlin homeowners ask us to, and we know the specific failure points that come with them.
Key Takeaways
- Paver driveway work in Summerlin runs $7,000 – $18,000 installed; patio work runs $3,500 – $11,000.
- Most failures show up at the joints and edges first, not in the paver faces.
- Our technicians bring up to 22 years of experience to the job.
- Written price, background-checked uniformed technicians, live phone coverage around the clock.
Which Mighty Buildings Models This Applies To

Mighty Buildings’ driveway and paver scope covers the hardscape interface around their prefab and panelized homes: the vehicle approach, the walkway transitions, aprons at garage and unit doors, and the patio fields off the main living wall. Where their assemblies depart from a standard tract home is at the tie-in points. The prefab foundation edge and utility chases want a specific edge-restraint profile, and the paver field has to meet the unit base at a set elevation so water sheds away from the wall rather than ponding against it.
Identify what you have before you order anything. Look for the stamped identification plate or sticker on the utility side of the building envelope, and record the model line and assembly date. Then measure the paver field itself: nominal paver dimensions, joint width, and the depth of the sand setting bed at an edge where you can lift one piece. Take a photo of an edge restraint at the garage apron; that’s where the profile is visible. Those four facts, model line, assembly date, paver dimension, and restraint profile, are what let us match the right spec.
On the OEM-versus-aftermarket question, our honest answer for Summerlin: match on dimension and unit weight, not on label. A paver is a dimensional product, and a correctly spec’d concrete or clay unit from a documented brand like Belgard or Unilock meets the same load and freeze-thaw criteria as a factory-supplied unit when the base and jointing are done right. What we won’t do is swap a restraint profile or change the base spec on a guess. The tie-in details are where an aftermarket part is fine and where it isn’t.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mighty Buildings Driveway & Pavers Is Failing
Summerlin hardscape failures are mostly about what happens underneath, not the top surface. The Mojave sun doesn’t crack good pavers; it cracks a base that was never compacted to depth, and the summer heat cycling does the rest. Here are the five symptoms we see, each with the cause behind it.
- Paver rocking or a hollow sound underfoot. The sand setting bed has washed out or the base course wasn’t compacted to depth, so the unit is sitting on a void. A single rocker usually means a locally failed base, not a bad paver.
- Joint sand washing out along the apron or slope edge. Improper edge restraint or a missing filter fabric lets storm runoff scour the joints at the low side, and the field starts to spread toward the edge. If you can see the base course through a joint, the restraint has given up.
- Ponding against the foundation. The finished field has settled at or below the elevation it was set to, and now water sits against the wall instead of running to the landscaping. On a Mighty Buildings unit, that’s the elevation at the tie-in point, and it’s what we check first.
- Widening joints and visible joint blowout in summer. Heat expansion with no allowance in the joint width squeezes the field and pops sand or, in the worst cases, shears a unit. Joint width is a spec, not a guess.
- Efflorescence and salt bloom on the paver faces. Moisture trapped between the bed and the underside of the paver wicks through and leaves white salt deposits. It’s cosmetic until it isn’t; persistent bloom usually means the base is holding water.
If you’re seeing any one of these and the field is more than a small section, the honest answer is a rebuild of the affected field, not a patch. A patch over a failed base will fail again by the next monsoon season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the price picture for Summerlin, written as a range because the range is real. It depends on field area, base depth, and how much existing hardscape has to come out.
| Item | Installed price range (Summerlin) |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Concrete driveway installation | $4,500 – $12,000 |
| Asphalt driveway paving | $3,500 – $9,000 |
| Driveway replacement | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
What drives the spread: field area is the biggest lever. Base removal and haul-off is next; in Summerlin, hardpan and existing concrete base often means a machine and a haul truck. Drainage correction adds to the job if the field has to be resloped to shed away from the unit. Paver selection matters less than most homeowners expect; a documented premium paver from Belgard or Unilock sits within a few points of a mid-grade unit at this scale. Every quote is a written line-item, so you see exactly what part of the range is base, what’s paver, and what’s waste removal. The 365-Day Done Right Promise covers the finished work: if it fails inside a year, we come back and correct it at no charge.
DIY or Call Us?
The safe division of labor is simple. What you can do: lift one unit at an edge on a dry day, take a photo of the base course, measure the joint width and paver thickness, and note where the water goes when it rains. That’s checking. What we won’t tell you to do is pull a whole field or rebuild the base yourself. Lifting pavers without a system for the sand bed does more damage than it fixes, and resetting a unit on a base you can’t see means you can’t know if the base is compacted.
The one place we say stop right now: never dig into the utility chase at the building wall to investigate a ponding issue. That’s where the utility runs are, and it’s the wrong place to learn by guessing. A paver driveway is a base problem, and base problems get diagnosed from the top with the right tools.
The good news is that most of this is repairable and correctly priced up front. Call (844) 588-0072 and we’ll put a written price in your hand before anyone touches the field.
FAQs

Properly based, 15 to 25 years is a realistic service life in this climate, and the paver itself is often the last thing to fail. The base, edge restraint, and joint sand are what set the actual number. The Mojave sun is hard on the surface, but the summer heat cycling and the monsoon runoff are what kill the assembly, so the base and restraint profile are where we put the money first. Call (844) 588-0072 for an exact quote on your field; estimates are free.
Sometimes, yes. If the failure is isolated to a small section and the base under the surrounding field is sound and compacted to depth, we rebuild that section and leave the rest. If the rockers or settled areas span more than a small share of the field, or if the base is visibly holding water, repair is a stopgap and the field comes back. We’ll tell you which one it is honestly, in writing, before the work starts.
A typical paver driveway replacement in Summerlin is a multi-day job, not a one-day swap; the base has to be excavated, compacted in lifts, and checked before any paver goes down. The spread is roughly two to five working days depending on field size and how much existing base comes out. If you’re keeping the field, a repair to a small section is shorter. Call (844) 588-0072 and we’ll give you a written scope and timeline for your driveway.
We match the part to the assembly, not to a label. We measure the field, identify the restraint profile and the elevation at the tie-in point, and spec a documented paver from a brand like Belgard or Unilock that meets the same dimension and load criteria. We don’t claim to stock Mighty Buildings parts, and we don’t carry parts on a truck; we source to the job’s spec with manufacturer documentation attached. For your own records and for warranty purposes, that’s a stronger paper trail than a factory label alone. Call (844) 588-0072 for a written quote on your Summerlin driveway or paver patio.
We also work on KraftMaid, Cambria, and Silestone installs on these same homes, so if the hardscape job turns up a kitchen or bath item while we’re there, we can scope it in the same visit.
The bottom line for a Summerlin homeowner with a failing driveway or paver field: you get a written price before work starts, background-checked uniformed technicians on the job, a live person on the phone whenever you call, and the 365-Day Done Right Promise on the finished work. Call (844) 588-0072 for a free estimate. We’ll put the numbers and the scope in writing, and the guarantee in your hand when we close.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












