







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Bathroom Remodeling: The Summerlin Owner’s Guide
Unilock bathroom remodeling in Summerlin runs $9,000 – $28,000 installed, and the tier your project lands in depends on wall prep, waterproofing, and fixture specification rather than on tile surface area alone. A typical hall bath with a tub-to-shower conversion and a single vanity sits near the low-to-middle of that range; a full primary bath re-pipe, double vanity, and floor-to-ceiling tile pushes toward the top.

Summerlin homeowners usually start asking about the wall assembly after a failed inspection or a soft spot at the shower curb. Waterproofing done on top of drywall instead of cement backer board is the number one thing we open up. The second is unsupported tile over a substrate that moves. If you’re pricing a Unilock project and want a real number instead of a range, call us at (844) 588-0072 and we’ll write the scope before anyone touches a tool.
Key Takeaways
- Full Unilock bathroom remodeling in Summerlin: $9,000 – $28,000 installed.
- Waterproofing failures behind tile are the most common cause of Unilock bathroom callbacks we see.
- Written price before work starts, verified in writing, not squeezed into the estimate conversation.
- Every completed bathroom carries the 365-Day Done Right Promise.
Which Unilock Models This Applies To

Unilock makes hardscape and wall systems, so “bathroom” here means the tile and paver wall products Unilock specifies for interior wet areas – the same dimensional lines you’d find on an exterior retaining wall or a pool coping. That matters when you’re matching a specific product line to a repair. Pool coping, wall caps, and thin veneer lines are typically sold by nominal dimensions and finish, not by a single model number stamped on the back of the piece. Pull a loose tile and photograph the back; the mold mark and the dimension give you the actual line.
The compatibility gotcha most Summerlin owners hit: an identical-looking finish from a hardware store off the shelf is rarely the same thickness or the same nominal size. A 1/16-inch thickness difference between an OEM Unilock piece and a lookalike means the tile setup shifts, and you get lippage at the joint that never closes. For visible or continuous surfaces, stick to the OEM tile or a confirmed equivalent that matches thickness and mold marks exactly.
The OEM-vs-aftermarket decision depends on where the piece lives. A hidden membrane or backer sheet? Aftermarket is fine and cheaper. A finished, visible Unilock wall or floor surface? OEM or a verified equivalent, every time. If you can’t identify the line from the sample, we’ll measure the joint layout and spec the closest match in writing before we order anything.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Bathroom Remodeling Is Failing
- Hairline cracks along the grout running straight rather than following the tile. That pattern is substrate movement, not grout wear. A backer board that wasn’t screwed to a solid stud before the tile went down will crack the grout within a season of heavy use.
- A soft spot or flex at the shower curb or the tile-to-tub joint. Water has already reached the wood or framing behind the waterproofing. When you press in and the tile gives a little, the substrate has failed and the tile needs to come up.
- Efflorescence – the white, chalky bloom on grout or tile edges. Moisture is wicking through the assembly and depositing salts on the surface. Common in older Summerlin builds where the original shower pan was set without a proper slope.
- Loose tile or a hollow clack when you tap. The thinset bond has released from the backer board or the board has released from the stud. Tapping with the handle of a screwdriver sounds hollow over the bad spot and solid over the good.
- Mold or damp smell at the base of the wall under the tile. Water is trapped behind the waterproofing with nowhere to drain. In Summerlin’s dry air this often hides until the wall is opened, because the surface dries fast and the assembly behind it doesn’t.
Replacement Cost & What’s Included
Bathroom remodeling in Summerlin runs $9,000 – $28,000 installed, and a small bathroom remodel runs $5,000 – $12,000. A tub-to-shower conversion is $3,500 – $10,000, a shower replacement is $3,000 – $8,500, a walk-in shower installation is $4,500 – $12,000, and a bathroom vanity installation is $800 – $3,000. The Unilock tile or wall product itself is usually a minority of the total. Labor, framing repair, waterproofing membrane, and fixture specification drive the range, not the tile cost.
Every price we give is written before work starts. No change orders at the door because the substrate turned out worse than the estimate. If it does, we stop, show you, and re-price in writing before anyone continues. Labor for the tile setting, membrane install, and fixture hang is included in the figure above; the tile and fixtures are line-itemed separately so you can see exactly what you’re paying for.

See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely pull a loose tile sample, photograph the mold mark, measure the joint to the nearest 1/16 inch, and match the finish to a Unilock sample board. You can also do a simple tap test along the wall and grout to find hollow spots, and photograph any efflorescence before you clean it, because the pattern tells a contractor what failed. Nobody should attempt to remove a wet-wall assembly without knowing if it’s been cut into the plumbing rough-in. Pulling tile over a shower valve, a supply line, or an electrical junction in the wall is a genuine shock and flood risk if you don’t know what’s behind it.
The other thing that goes wrong with DIY: you re-tile over the same failed substrate. We’ve opened walls in Summerlin where a homeowner laid a second layer of tile over the first and the whole assembly failed within two years because the water had nowhere to go. Call (844) 588-0072 before you start pulling tile. We’ll tell you on the phone whether it sounds like a substrate failure or a fixture failure, and if it’s worth a repair versus a full replacement.
FAQs

How long does Unilock bathroom remodeling last in Summerlin? A correctly installed tile wall over a cement backer board and a properly sloped shower pan will last 20 to 30 years. The failure you’ll see first in Summerlin isn’t the tile – it’s the waterproofing membrane. Our dry air dries the surface fast, so a membrane that’s leaking behind the wall doesn’t announce itself until the framing behind it is soft. Call (844) 588-0072 if you want an inspection before the wall starts feeling soft. Estimates are free.
Can I repair a failing shower wall instead of replacing the whole bathroom? Sometimes, yes. If one or two tiles are loose and the substrate behind them is still solid, a local repair holds and costs far less than a full replacement. If the failure follows a straight crack along the grout line or the curb is soft, the whole assembly has to come out – patching over it just buys six months. Call (844) 588-0072 and we’ll tell you which one you’re looking at before quoting anything.
How long does the swap take? A single-wall tile repair or a vanity replacement is typically a two-to-three-day job. A full tub-to-shower conversion with new waterproofing, backer board, tile, and fixtures runs seven to twelve working days depending on the scope and inspection schedule. We’ll put the exact schedule in writing before the crew starts and call you if anything changes.
How do you source the Unilock bathroom product? We specify against the brand roster we work with regularly, which includes Unilock for tile and hardscape, plus KraftMaid, Cambria, and Silestone when a bathroom project moves into a vanity or surface upgrade. Every spec sheet is attached to the written scope so the tile line, thickness, and finish are traceable. Bradford Remodeling Co Summerlin is an independent service provider and is not affiliated with Unilock.
Will the price change once work starts? No. We give you a written price before anyone touches the wall. If the substrate turns out worse than we saw during the estimate, we stop, show you the damage, and re-price in writing before continuing. That’s how The Garrison Standard works on every Bradford project. Call (844) 588-0072 to schedule a free estimate.
Contact Us for a Written Price
If your Unilock bathroom project in Summerlin is stuck between a failing shower wall and a quote you can’t trust, call Bradford Remodeling Co Summerlin at (844) 588-0072. A live person answers, 24 hours a day, and we’ll schedule a free estimate at a time that works for you. You’ll get a written scope and a real number before a single tile moves. Every completed bathroom carries the 365-Day Done Right Promise, and our background-checked, uniformed technicians will arrive knowing exactly what’s on the schedule. Bradford Remodeling Co Summerlin is a member of the Garrison Partners family, independently owned and operated, and held to The Garrison Standard on every job.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












