







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Driveway & Pavers: The Summerlin Owner’s Guide
We install and repair Boral driveway and paver systems across Summerlin, and a full paver driveway runs $7,000 – $18,000 installed depending on square footage, base prep, and whether the existing concrete or asphalt has to come out. Paver patios land at $3,500 – $11,000, and spot repairs to a settled or heaving section are usually a fraction of a full replacement. We’re an independent service provider, not affiliated with Boral, so our quotes reflect labor and site conditions in Summerlin, not a manufacturer’s suggested retail number. Call (844) 588-0072 for a written price before any work starts.

Owners in Summerlin usually find the problem the same way. A paver near the driveway apron rocks underfoot when the car rolls over it. Sand washes out of the joints after a monsoon rain and the grid starts to spread. Or a hairline crack opens along the border course and grows a little wider every summer. By the time you’re sweeping sand back into the joints for the third time in a season, the base has already moved. That’s the part that failed, not the paver itself.
Key Takeaways
- Boral paver driveways in Summerlin: $7,000 – $18,000 installed. Patios: $3,500 – $11,000.
- Most “failed pavers” are actually failed base and joint sand, not failed stone.
- Summerlin’s caliche-heavy soil and monsoon runoff are the two most common causes we see.
- Every project gets a written price up front and the 365-Day Done Right Promise in writing.
Which Boral Models This Applies To

Boral’s paver lines cover a lot of ground, and the part that matters on a repair is almost never the surface stone. What fails is the bedding layer, the joint sand, the edge restraint, or the compacted base underneath. That said, matching the surface paver correctly matters if you’re replacing individual units, because Boral’s profiles are not interchangeable across series.
The common Boral paver profiles you’ll find on Summerlin driveways include the standard 4×8 and 4×9 rectangular units, the larger 12×12 and 16×16 squares used on patios, and the interlocking shapes sold under Boral’s structural paver lines. Thickness is the spec that trips people up. Driveway-rated pavers are typically 2 3/8 inches or thicker; patio and walkway pavers often run 1 5/8 to 2 inches. Lay a thinner patio unit in a driveway and it will crack within a couple of seasons under a loaded SUV.
To identify what you have, pull one loose paver from an inconspicuous spot and measure length, width, and thickness with a tape. Look for a stamp or mold mark on the underside. Boral pavers often carry a manufacturer mark, though older units may not. If there’s no mark, bring the paver to us or send a photo with dimensions. We match by profile and thickness, not by guessing at color names, because dye lots vary year to year and an exact color match on a weathered driveway is rarely possible. We’ll tell you that up front rather than promise a blend that won’t hold.
On the OEM-versus-aftermarket question: for base material, joint sand, and edge restraint, there’s no reason to chase a Boral-branded part. Polymeric sand and a proper edge restraint from any reputable maker do the job. For visible surface pavers, matching the original profile and thickness matters most, and a quality compatible paver in a close color is usually the honest answer on a repair. If you’re also refreshing interior surfaces during the project, we handle KraftMaid, Cambria, and Silestone work as well.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Driveway & Pavers Is Failing
- Pavers rocking or flexing underfoot. The bedding sand has thinned or the base wasn’t compacted to depth. Movement lets water in, and water is what finishes the job.
- Sand washing out of the joints after rain. This is the signature Summerlin failure. Monsoon sheets run across a driveway that slopes toward the street and strip the joint sand, then the pavers lose their interlock.
- Heaving or a raised hump in one section. Usually a tree root lifting the base or a section of base that wasn’t excavated deep enough over caliche. Caliche is the cemented calcium layer under much of Summerlin’s soil, and it doesn’t drain.
- Edge pavers spreading outward. The edge restraint has failed or was never pinned properly. Once the border moves, the whole field loosens from the outside in.
- Cracks running through individual pavers. Point-load failure from a too-thin paver, a hollow spot in the bedding, or a vehicle heavier than the driveway was built for. Cracks in the stone itself are the one symptom that points at the paver rather than the base.
Two of these together, especially rocking pavers plus sand loss, means the base is compromised and a surface patch won’t hold. One cracked paver with a stable field around it is a swap, not a rebuild.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what Summerlin homeowners actually pay, installed:
| Scope | Installed Price Range |
|---|---|
| Full paver driveway installation | $7,000 – $18,000 |
| Paver patio installation | $3,500 – $11,000 |
| Driveway replacement (tear-out and rebuild) | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
What moves the number: square footage first, then base depth. A driveway over solid, well-draining subgrade needs less excavation than one sitting on caliche that has to be broken and hauled off. Tear-out of an existing concrete or asphalt slab adds cost. Border courses, curves, and cutting around a driveway apron add labor. Sealing is a maintenance line item, not a repair, and it won’t fix movement.

Every quote is a written, line-item price before any work starts. No numbers that move at the door. Labor and material are separated so you can see what the pavers cost versus what the base prep costs. All completed work carries the 365-Day Done Right Promise: if it fails within a year, we come back and correct it at no charge, and you hold that guarantee in writing at close.
DIY or Call Us?
You can safely do a few things yourself. Sweep and refill joint sand once a season. Pull a loose paver and measure it so we can match the profile. Check that your downspouts and grading send water away from the driveway rather than across it. Rinse the surface and look for low spots after a rain. None of that is risky.
Where DIY tends to go wrong is base repair. Rebuilding a settled section means excavating to depth, re-compacting in lifts, and re-setting edge restraint. Skip the compaction and the repair fails within a season, usually worse than before. There’s also a genuine hazard most homeowners don’t think about: a lifted or rocking paver at the edge of a driveway is a trip point, and a heaving section near a walkway catches a foot or a walker wheel. Loose pavers on a slope can also slide under load.
If you’ve got movement across more than a couple of pavers, that’s our call to make, not yours. Call (844) 588-0072 and we’ll give you a written price for the repair before anything gets torn up.
FAQs

The pavers themselves often last 25 to 50 years. The part that fails first is the joint sand and base, which typically needs attention every 5 to 10 years in Summerlin’s heat and monsoon cycle, well before the stone wears out.
Often yes. If the movement is isolated to one section, we lift those pavers, rebuild the base, re-set them, and re-sand. If the failure runs across the whole field, a full rebuild is the honest answer, and we’ll tell you which one you’re looking at.
A spot repair is typically a day. A full driveway rebuild usually runs 3 to 5 days depending on square footage, tear-out, and weather. You’ll get the schedule in writing with the price.
We match by profile, thickness, and dimensions rather than color name, and we source through documented supplier channels. On visible repairs we’re upfront that an exact color match to a weathered driveway isn’t realistic, and we’ll show you the blend options before ordering.
Call (844) 588-0072 to schedule your free estimate. A live person answers, day or night. Our technicians have up to 22 years of experience, they’re background-checked and uniformed, and you’ll have a written price and a signed guarantee in your hand before we call the job done.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












