







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Grohe Bathroom Remodeling: The Summerlin Owner’s Guide
Grohe-compatible bathroom remodeling in Summerlin runs $9,000 – $28,000 installed, and that number is written down before any work starts. The range covers everything from swapping a failing Grohe fixture and rebuilding the wet wall around it to a full bathroom remodel where the Grohe shower system, thermostat, or fill valve is the anchor piece. Small bathroom remodels land lower, in the $5,000 – $12,000 band. What almost never works is replacing a Grohe part alone on an old valve body: the cartridge is fine, the seat behind it isn’t, and the drip returns within weeks.

Most Summerlin owners find this problem the same way. First it’s a shower that won’t hold temperature, so you nudge the thermostat handle a few degrees and live with it. Then the drip at the tub spout starts, or the rainfall head runs weak on one side. By the time the ceiling stain shows up in the room below, the rough-in has been seeping for months. That’s normally the moment we get the call.
Key takeaways
- Installed Grohe bathroom remodeling in Summerlin: $9,000 – $28,000, written price before work starts.
- Grohe thermostatic cartridges typically last 8 – 12 years in Las Vegas Valley water; hardness here runs hard enough to chew through seals faster than most national guides suggest.
- We’re an independent remodeling contractor, not affiliated with Grohe. We install and service Grohe-compatible systems.
- Every finished project carries the 365-Day Done Right Promise: if it fails inside a year, we come back and correct it at no charge.
Which Grohe Models This Applies To

Most of the Grohe work we see in Summerlin bathrooms falls into four families. The Grohtherm line and its thermostatic shower valves use a wax or paraffin thermoelement cartridge, and that element is the part that fails first. The Grohe Eurosmart and Grohe Concetto single-lever basin and kitchen faucets use a 35mm ceramic cartridge, and there’s a smaller 28mm cartridge on some compact models. The Grohe Rainshower and Tempesta hand showers use a distinct thread and cone fitting, not a generic 1/2-inch NPT connection. Grohe Sensia and shower-toilet units carry their own electronic fill and flush assemblies.
Identifying the right part matters more than most people expect. Look on the underside of the faucet body or the back of the valve trim for the model number, usually a six-digit figure like 33 755 or 19 926. Then measure the cartridge diameter with calipers before ordering; pulling a 35mm cartridge and finding a 28mm one on the shelf is the most common mistake we see. On the OEM-versus-aftermarket question, Grohe’s own cartridges and thermoelements are what we install. The aftermarket equivalents save maybe $20 – $40 on a part, and that savings rides on a seal that can fail in 18 months. On a $9,000 – $28,000 bathroom remodel, that’s a decision you make once and not again.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Grohe Bathroom Remodeling Is Failing
None of these symptoms are cosmetic. Each one points to a specific part inside the fixture, and each gets worse with the Las Vegas Valley’s hard water and the temperature swings Summerlin bathrooms see between a winter morning and a July afternoon.
- The shower won’t hold temperature. You set it to 100°F and it drifts toward scalding or cold within a minute. That’s the thermostatic cartridge’s wax element losing its calibration – the part that fails most often on Grohtherm valves.
- A steady drip at the tub spout or basin aerator. Water keeps running after the handle is shut off. That’s a worn ceramic cartridge seat or a scored valve seat behind it, and left alone it stains the fixture and pushes your water bill up.
- Water pressure drops only when the shower runs hot. Hot-side restriction usually points to scale buildup in the cartridge or a blocked thermoelement port – common in Summerlin because the local water carries dissolved minerals that deposit inside the valve body.
- The handle feels spongy or won’t return to center. The cartridge’s internal stops have worn, or the retainer nut has backed off. It’s a small part, and it’s what holds the whole assembly steady.
- Water shows up on the ceiling below the bathroom. This is the one to take seriously. It means the rough-in valve body or a supply connection behind the wall has been seeping, and the drywall is the last thing holding the water back.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Bathroom remodeling in Summerlin with Grohe-compatible fixtures as the anchor piece runs $9,000 – $28,000 installed. A small bathroom remodel sits in the $5,000 – $12,000 range. If your scope is narrower, the line-item ranges look like this:
| Scope | Installed price range |
|---|---|
| Bathroom remodel (full) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What drives the number: whether the rough-in valve body gets replaced or just the cartridge, whether tile and substrate come out with it, and whether the waterproofing membrane behind the shower tile is intact. Our written price itemizes the Grohe-compatible parts, the labor, and the disposal. Nothing moves at the door. The 365-Day Done Right Promise covers every completed project for a full year; if the installation fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
You can safely check a few things yourself. Shutoff valves under the vanity turn by hand. Cartridge model numbers are stamped on the part or printed on the valve trim. You can watch a drip under the sink and see where it originates. What you shouldn’t do is open the wall around a rough-in valve or pry a cartridge out of a live thermostatic body. The cartridge sits under spring load, water is behind it whether or not you think you shut off the supply, and a brass valve body with scale buildup can crack when a tool slips. That’s not a scare tactic; it’s the reason we don’t send homeowners into that wall.
The other issue is tile and waterproofing. Removing a Grohe shower valve often means cutting the cement board or the waterproofing layer behind it. If that membrane goes back together wrong, water gets behind the tile and stays there. That failure shows up six months later and costs more than the original repair. Call (844) 588-0072 to schedule a free estimate. A live person answers the phone, day or night.
FAQs

Eight to twelve years is realistic in the Las Vegas Valley, and often closer to eight on hard-water Summerlin properties. Summerlin’s water carries enough mineral content that scale deposits inside the valve body faster than in softer markets, which is why we see thermostatic cartridges fail early here. If you’re past year eight and seeing temperature drift, plan for the replacement. Call (844) 588-0072 for an exact quote on your Grohe model – estimates are free.
Sometimes, but not often. On ceramic cartridges, cleaning scale off the seat can buy another year or two if the ceramic disc itself is intact. Once the disc is scored or the thermoelement has lost calibration, repair is a delay, not a fix. The part is what fails, and the part is what gets replaced. Call (844) 588-0072 and we’ll tell you honestly whether it’s a clean-and-reseat job or a replacement before anyone starts work.
A single cartridge swap runs roughly one to two hours once access is open. A full bathroom remodel in Summerlin is a multi-week project, and the schedule lives in writing alongside the price. Because the scope varies this widely, the honest answer always starts with a free estimate rather than a promise made over the phone. Call (844) 588-0072 to schedule yours.
We order by model number and cartridge diameter, checked against the fixture before we commit. We don’t claim to carry parts on a truck or stock Grohe parts locally, and we’re an independent remodeling contractor, not affiliated with Grohe. We also install KraftMaid, Cambria, and Silestone alongside the Grohe fixtures when a Summerlin bathroom needs cabinetry and surface work done in the same scope, so the specs stay traceable from the fixture to the vanity to the countertop. Call (844) 588-0072 to schedule a free estimate with a written price before any work starts.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












