







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Kitchen Remodeling: The Summerlin Owner’s Guide
Kohler kitchen remodeling in Summerlin runs $14,000 – $45,000 for a full kitchen, and most of that number is cabinetry, surfaces and labor, not the fixture. If you came here with a Kohler product that failed, the honest answer is that Kohler makes faucets, sinks, and a handful of kitchen components, not the part that just broke on your cabinets or counters. Most Summerlin owners who land on a page like this have either a Kohler faucet dripping into the cabinet base, a Kohler sink that’s pulling away from a stone counter, or a Kohler filtration or soap dispenser unit that quit. We install and replace all three, and we’ll tell you plainly which of them is a part swap and which is a remodel.

Here’s what usually happens: you notice water pooling under the sink cabinet in your Summerlin kitchen, or the handle on a Kohler pull-down doesn’t seat the way it used to. By the time you find the model number, half the research is spent just figuring out whether you’re replacing a cartridge or a countertop. This page is built to get you past that fast.
Key Takeaways
- Full Kohler-inclusive kitchen remodels in Summerlin: $14,000 – $45,000; fixture-only swaps sit far below that.
- Kohler uses series-specific cartridges and mounting hardware, so the model number matters more than the brand name.
- Our technicians have up to 22 years of experience with brands including Kohler, Moen, KraftMaid, and Cambria.
- Every job gets a written price before work starts and a 365-Day Done Right Promise in writing at close.
Which Kohler Models This Applies To

Kohler’s kitchen faucets break into a few families, and they don’t share parts. The Artifacts and Purist pull-downs use different cartridge assemblies than the Simplice or Bellera lines, even when the handles look nearly identical on the showroom floor. Sinks have their own split: the Riverby and Whitehaven cast iron apron-front models carry a specific undermount mounting kit and weight that a standard stainless sink clip set won’t hold. That incompatibility is the gotcha that bites most Summerlin DIY replacements, because the apron-front sink in a Summerlin kitchen weighs enough that the wrong bracket lets it separate from the counter over a season or two.
To identify what you actually have, pull the faucet’s aerator and look for a stamped model code, or check the escutcheon (the plate the faucet sits on) for a series stamp. Sinks carry the Kohler mark and a model number on the underside rim, visible with a phone camera and a flashlight. Once you have that number, the OEM-versus-aftermarket call is straightforward: Kohler OEM cartridges and mounting hardware are made to Kohler’s spec and hold their dimensions, which matters in Summerlin’s hard water because a poorly matched cartridge wears its seals faster. A quality aftermarket equivalent is fine for a soap dispenser or a spray head; for the cartridge inside a $400 faucet body, we recommend OEM. We don’t stock parts and we don’t carry them on a truck. We source the right one for your model and install it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Kohler Kitchen Remodeling Is Failing
These are the five symptoms we see most in Summerlin homes, and what’s usually underneath each one.
- Water pooling under the sink cabinet. Nine times out of ten it’s a failed cartridge seal or a loose supply connection, not a cracked sink. Left alone, the cabinet substrate (the wood panel the sink sits on) swells and the repair grows into a cabinet and countertop job.
- The faucet handle won’t hold position or drips when closed. The cartridge has worn or mineral has packed into the valve. Summerlin’s hard water leaves calcium deposits that shorten cartridge life well below the manufacturer’s general estimate.
- The apron-front sink is separating from the counter. The mounting brackets have loosened or the original installer used the wrong kit for the sink’s weight. This one is a structural fix, not a parts swap.
- A soap dispenser or filtration faucet drips from the base. The pump seal or the O-ring at the shank has dried out. Cheap to replace, but only if you match the shank diameter to the existing countertop hole.
- The spray head won’t retract or leaks at the connection. The hose guide or the diverter has failed. On pull-down models this is often a hose-and-guide replacement rather than a whole-faucet job.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest spread for Summerlin, line-item, so you know what you’re looking at before anyone knocks on your door.
| Job | Installed price range |
|---|---|
| Kitchen remodel (full) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: whether the counter has to come off to reach the sink mounting kit, whether the cabinet substrate under the sink needs replacing, and the stone you choose. The price you get is written before work starts, no numbers that move at the door. Every completed job is covered by the 365-Day Done Right Promise: if the work fails within that year, we come back and correct it at no charge.
DIY or Call Us?
You can safely check an aerator screen, swap a soap dispenser pump, or replace a spray head on a Kohler pull-down. Those are low-risk and don’t involve the water supply line under pressure. What you shouldn’t do is pull a faucet cartridge on a stuck valve or try to re-seat an apron-front sink yourself. The first risks a snapped valve body and water in a finished cabinet; the second risks a heavy cast iron sink letting go. Both are the kind of mistake that turns a small fix into a countertop and cabinet replacement. We work on a documented roster of name-brand fixtures, and a live person answers the phone day or night to tell you which category your problem falls in. Call (844) 588-0072 for a free estimate and a written price.
FAQs

Expect shorter life in Summerlin than the manufacturer’s general estimate because of hard water. Mineral buildup can wear a cartridge in a few years here versus much longer in softer-water regions, so annual aerator cleaning buys you real time.
Often yes. A dripping Kohler faucet usually needs a cartridge and O-rings, not a new faucet, and a spray head that won’t retract is often a hose guide. The fix that isn’t repairable is a separated apron-front sink, which needs the correct mounting kit and re-seating.
A faucet cartridge or spray head swap is a short job, typically under an hour once the correct part is on hand. Sink re-seating or anything that requires pulling the counter takes longer, and we schedule it as its own visit.
We match the model number off your faucet or sink and order the OEM part to that spec. We don’t stock parts, but we do confirm compatibility before we arrive so the job isn’t delayed by a wrong fit. Kohler is one of many documented brands we install, alongside KraftMaid, Cambria, and Silestone. Call (844) 588-0072 for a free estimate.
Bradford Remodeling Co Summerlin is an independent service provider, not affiliated with Kohler. If a Kohler fixture in your Summerlin kitchen has failed, get a written price before any work starts and a guarantee that covers the repair for a full year. Call (844) 588-0072 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Summerlin, serving Summerlin and nearby areas.












